Nederland Mining Museum—Sales Inventory

#1  Rake classifier, 15’ x 36” wide x 24” deep, square trough with gear and shaft +    fittings. Rusty, bottom rusted out in places.  $250.

#2   Classifying screen (trommel) 3’ long x 24” diameter. Rusty.  $50  Not pictured

#3   Horizontal boiler, Hendrie & Bolthoff, 1890’s.  10’ long x 5’6” tall x 42” diameter.  Other half of round door comes with it. $900

#4        Vertical air compressor tank 7’ high x 2’ diameter (on right) $250

#5        Vertical air compressor tank 7’ high x 30” diameter (on left) $300

#6        Shaker table frame and drive train.  Frame is a 12” x 16” x 16’ beam with three wood trestles for the table, the drive train at one end. The shaker table is separate, 6’x 11’ x 6” deep (not pictured).  Shaker table with frame and drive, $2,000. 

#7        Mine vent blower on iron frame, rusted. 3’ long x 2’ diameter drum on 3’ x 4’ frame.  $75  Not pictured.

#8        Line shaft with 5 pulleys, 16’.  Whole assembly, $375.  Pulleys: (1) 16” straight spoke,  $90; (2) 12” with pre-1890’s curved spokes, $90 each; (2) 8”straight spoke, $60 each.

#9        Iron shaker table base frame. 2’ x 20’, twin I-beams, NO TABLE. $200 Picture shows frame under two broken drive wheels from another item.

#10      Sullivan WG6 Two-flywheel compressor. 40” wheels, 6 ½ ‘ x 30” wide.  $600

#11      Small hoist, broken wheel, with a Chevy engine (non-working). 4’x 4’x 8’ long.  $350

#12      Jaw Crusher, from local mine, broken flywheels. 4’ x 4’x 6’. Broken flywheel separated, comes with Crusher.  $2000

#13      Ore Feeder—works perfectly!—with original wooden pulley. 10’ x 5’ x 5’.  $1000.  Picture shows feeder on its side

#14      1901 Hoist with cable, 4’ drum on 6’ wooden frame. Needs power plant.  $1000.    (Wood beam in picture belongs to a different item)

#15      Wood timber frame with line shaft pulleys. 3’ x 3’ x 5’.  $350 Picture shows frame on its side.  It works!

#16      10 hp. “Hothead” diesel engine, Fairbanks-Morse (does not run). With 40”  wheels on iron frame, 3’ wide, 4 ½ ‘ under engine, 4 ½ ‘ behind engine. $500

#17      Stator Coil/Rotor, about 36” diameter with wood belt pulley. $300 Turns over smoothly.

#18      Ortway Induction Motor 440 v.  30” diameter.  Works!  $300

#19      Large 18” x 10” wide spoked pulley on axel. Excellent condition.  $200

#20      Westinghouse Electric CCL Induction Motor 15 hp, 60 cycle, 440 v. 1930’s, double shaft, runs.  About 30” diameter.  $200

#21      Kohler gasoline generator with hand crank, 4 cyl. 1930’s.  $1,000.

#22      Double winch (‘slusher’) on metal frame, with horizontal wheel attached. 1950’s.  $50.  Photo is top view.

#23      Lorain rock shovel, 6 cyl, Model D318.  $6,000.  Caterpillar diesel engine with 2-cylindar pony motor.  Runs perfect.